Workshop/How to Fix Ghosting and Ringing in 3D Prints

How to Fix Ghosting and Ringing in 3D Prints

This article may contain affiliate links. If you make a purchase through these links, we may earn a small commission at no extra cost to you. This helps us keep creating free content.

How to Fix Ghosting and Ringing in 3D Prints

You print what should be a smooth, flat surface and instead get a series of faint ripples radiating outward from every corner, letter, or sharp feature. The ripples fade over a few millimeters but they're clearly visible, especially in directional light. This artifact is called "ringing" (also called "ghosting" or "echoing"), and it's one of the most common quality issues in FDM printing, especially at higher speeds.

Ringing is a mechanical resonance problem, not a slicer or material problem. Here's what causes it and how to fix it systematically.

What Causes Ringing

When your printhead changes direction sharply, at a corner or after a straight move, the sudden deceleration and re-acceleration excites vibrations in the mechanical system. These vibrations cause the nozzle to wobble slightly relative to where it should be, and those wobbles deposit filament in a wavy pattern instead of a straight line.

How to Fix Ghosting and Ringing in 3D Prints β€” practical guide overview
How to Fix Ghosting and Ringing in 3D Prints

The intensity of ringing depends on three factors: how fast the printhead was moving before the direction change (higher speed = more kinetic energy = more vibration), how heavy the moving mass is (heavier printhead or bed = more momentum = worse ringing), and how rigid the mechanical system is (loose belts, wobbly frame = vibrations persist longer).

Key insight: Ringing artifacts always appear AFTER a sharp feature, not before it. The ripples trail away from corners in the direction of travel. If you see artifacts before a feature, that's a different problem, likely pressure advance issues or backlash.

Fix 1: Tighten Your Belts

🧴

Magigoo Original 50 mL Adhesive

All-in-one bed adhesive for PLA/PETG/ABS, sticks while hot, releases when cool.

As an Amazon Associate we earn from qualifying purchases.

See on Amazon β†’

Loose belts are the number one cause of ringing in printers that previously printed cleanly. A belt that's lost tension can't precisely control the printhead position during rapid direction changes, allowing the head to overshoot and oscillate.

Check both your X and Y axis belts. They should be firm but not guitar-string tight, pressing the belt with a finger should deflect it about 2-3 mm on a typical 300 mm run. Many printers have built-in belt tensioners (Prusa, Bambu Lab, Voron). If yours doesn't, loosen the motor mount, pull the belt taut, and re-tighten the mount.

Quick test: Pluck the belt like a guitar string. A properly tensioned belt on a 300 mm span should produce a low thrum around 80-100 Hz. If it sounds floppy and low-pitched, it needs tightening. If it's extremely high-pitched and barely deflects, it's over-tensioned and will wear the bearings.

How to Fix Ghosting and Ringing in 3D Prints β€” step-by-step visual example
How to Fix Ghosting and Ringing in 3D Prints

Fix 2: Reduce Acceleration and Speed

The most direct fix for ringing is to reduce how aggressively the printer changes direction. Two settings control this in your firmware:

Acceleration: How quickly the printhead speeds up and slows down (mm/sΒ²). Lower acceleration means gentler direction changes and less vibration excitation. Stock Ender 3 acceleration is 500 mm/sΒ². Modern fast printers run 5,000-20,000 mm/sΒ². If you have ringing, try halving your acceleration value and observe the results.

Jerk (or junction deviation): The maximum instantaneous speed change the printer allows at direction changes (mm/s). Higher jerk means the printer slams into corners at speed. Lower jerk means it decelerates more before corners. Try reducing jerk from the default (often 8-10 mm/s on Marlin) to 5-6 mm/s.

Pro tip: Reduce acceleration first, then jerk. Acceleration has a larger effect on ringing than jerk, and reducing it has a more predictable impact on print time. Cutting acceleration from 3,000 to 1,500 mm/sΒ² typically adds 10-15% to print time while dramatically reducing ringing. Cutting jerk has a smaller effect on both ringing and print time.

Fix 3: Reduce Print Speed

Speed and ringing are directly related, the faster you print, the more kinetic energy the printhead carries at direction changes, and the worse the ringing. If you're printing at 150 mm/s and seeing ringing, try 80-100 mm/s. In many cases, this alone eliminates the artifact.

The nuance: ringing primarily occurs during perimeter moves (the visible outer walls). You can often keep infill and travel speeds high while reducing only the outer wall speed. In your slicer, look for "outer wall speed" or "external perimeter speed" and set it to 50-70% of your inner wall speed. This preserves most of your time savings while cleaning up the visible surfaces.

Fix 4: Reduce Moving Mass

Less mass = less momentum = less ringing. This is why CoreXY printers ring less than bed-slingers at the same speed, the lightweight printhead has far less mass than a heavy heated bed moving in Y.

On a Cartesian bed-slinger: Replace a heavy glass bed with a lighter PEI spring steel sheet (saves 200-400g). Remove unnecessary accessories from the printhead (heavy fan ducts, large LEDs). Every gram you remove from the moving axis improves ringing performance.

On a CoreXY: Ensure the toolhead is as light as possible. Lightweight extruders like the Bondtech LGX Lite or Sherpa Mini shave 50-100g compared to stock options. On a Voron, the difference between a heavy Stealthburner and a lightweight Mini Stealthburner is visible in print quality at high speeds.

Fix 5: Enable Input Shaping

Input shaping is the most effective solution and has become standard on modern printers. It uses an accelerometer to measure your printer's exact resonance frequencies, then adjusts motor commands in real-time to cancel those frequencies before they create visible artifacts.

If your printer runs Klipper firmware, input shaping is built in. Mount an ADXL345 accelerometer on the printhead, run the calibration routine, and Klipper generates compensation values. The improvement is dramatic, printers that showed heavy ringing at 100 mm/s can print at 300+ mm/s with clean surfaces after input shaper calibration.

Bambu Lab printers run input shaping automatically during their vibration compensation calibration. Prusa MK4 and XL include it in their firmware. If you have a Marlin-based printer, consider switching to Klipper specifically for this feature, it's worth the effort.

Watch out: Input shaping masks the symptoms of mechanical problems but doesn't fix them. If your belts are loose or your frame is wobbly, input shaping will reduce ringing but the underlying issues will still cause dimensional inaccuracy and premature wear. Fix the hardware first, then enable input shaping for the final polish.

Diagnostic Checklist

Work through these fixes in order. Each step either solves the problem or narrows down the cause:

  • Step 1: Print a ringing test model (search "ringing test" on Printables) at your normal speed. Photograph the results for comparison.
  • Step 2: Check and tighten belts. Reprint the test model. Compare.
  • Step 3: Check frame rigidity, grab the gantry and try to wobble it. Tighten any loose frame bolts. Reprint and compare.
  • Step 4: Reduce acceleration by 50%. Reprint and compare.
  • Step 5: Reduce outer wall speed by 40%. Reprint and compare.
  • Step 6: If ringing persists, enable input shaping (Klipper) or run vibration compensation (Bambu Lab, Prusa).

Most users solve their ringing by step 3 or 4. If you've gone through all six steps and still have artifacts, the issue may be a worn linear bearing, a bent lead screw, or a cracked printed part in the motion system, inspect the mechanical components for wear.

For related quality troubleshooting, see our guides on fixing stringing and complete printer calibration.

Want artifact-free prints at high speed? Our Klipper firmware guide walks through installation and input shaper setup for any printer.

Published by the 3D Printer Stuff editorial team. Published November 22, 2026.

Editorial responsibility: see Imprint.

Spotted an error or have something to add? corrections@3dprinterstuff.com

Share with fellow makers:
troubleshootingqualityfirmwarecalibration
πŸ“–

Explore more

All articles on 3D Printer Stuff β†’

πŸ”§

Maker Tips, Delivered

New guides, filament tests, and project ideas β€” every week in your inbox.

🎁 Free bonus: 3D Printing Starter Checklist (PDF)

🧭Part of our topic hub: Printer Hardwareβ†’

You might also like

Comments (0)

Leave a comment

Comments are reviewed before publishing.