Workshop/3D Printing Miniatures: Resin Settings for Perfect Detail

3D Printing Miniatures: Resin Settings for Perfect Detail

This article may contain affiliate links. If you make a purchase through these links, we may earn a small commission at no extra cost to you. This helps us keep creating free content.

3D Printing Miniatures: Resin Settings for Perfect Detail

If you've ever held a well-printed resin miniature next to an FDM one, the difference is immediately obvious. Layer lines essentially vanish at 0.03 mm layer height. Surface details, chainmail textures, facial features, tiny weapons, resolve with a crispness that makes the model look like it came from a professional mold, not a desktop printer.

But getting there requires dialing in your settings precisely. Too much exposure and you lose detail to light bleed. Too little and supports fail, layers delaminate, and your mini turns into a resin puddle on the FEP. The workflow below covers machines from an Elegoo Mars to an Anycubic Photon Mono M5s and is built for consistently perfect results.

Layer Height: How Low Should You Go?

For tabletop miniatures (28 mm to 32 mm scale), the sweet spot is 0.03 mm (30 microns). At this layer height, individual layers are invisible to the naked eye, even on smooth curved surfaces like cloaks and faces. Print time increases compared to 0.05 mm, but the quality difference on small models is dramatic.

3D Printing Miniatures: Resin Settings for Perfect Detail — practical guide overview
3D Printing Miniatures: Resin Settings for Perfect Detail

For larger display pieces (75 mm+), you can use 0.04 mm or even 0.05 mm without visible quality loss. The larger the model, the less layer lines matter because viewing distance increases.

Data point: A standard 32 mm heroic-scale miniature at 0.03 mm layer height takes roughly 2.5-3 hours to print. At 0.05 mm, that drops to about 1.5-2 hours. The extra hour buys you noticeably sharper detail on faces, hands, and small accessories.

Exposure Settings by Resin Type

💎

Elegoo Saturn 4 Ultra 16K

10″ 16K Mono LCD, smart resin tank heater, 150 mm/h, large-format resin for serious miniatures.

As an Amazon Associate we earn from qualifying purchases.

See on Amazon →

Exposure time is the single most critical variable for miniature quality. These are my tested starting points for a monochrome MSLA printer (Elegoo Mars 4, Saturn 3, Anycubic M5s, or similar) at 0.03 mm layer height:

Standard grey resin (Elegoo, Anycubic, Siraya Tech Fast):

  • Normal exposure: 1.8-2.2 seconds
  • Bottom exposure: 25-30 seconds (6 bottom layers)
  • Light-off delay: 1.5 seconds
  • Lift speed: 60 mm/min (retract), 150 mm/min (reset)
  • Lift distance: 5 mm
3D Printing Miniatures: Resin Settings for Perfect Detail — step-by-step visual example
3D Printing Miniatures: Resin Settings for Perfect Detail

Water-washable resin (Elegoo, Anycubic):

  • Normal exposure: 2.0-2.5 seconds (slightly higher, water-washable resins are less reactive)
  • Bottom exposure: 30-35 seconds (6 bottom layers)
  • Lift speed: 50 mm/min (slower, water-washable resins are softer during printing)

ABS-like resin (Siraya Tech Tenacious blend, Elegoo ABS-like):

  • Normal exposure: 2.5-3.0 seconds
  • Bottom exposure: 35-40 seconds (8 bottom layers)
  • These resins are tougher but need more light energy to polymerize fully
3D Printing Miniatures: Resin Settings for Perfect Detail — helpful reference illustration
3D Printing Miniatures: Resin Settings for Perfect Detail
Always run an exposure test. Every printer, resin batch, and LED panel ages differently. Print a validation matrix (like the Cones of Calibration or RERF test) whenever you open a new bottle of resin. Your optimal exposure might differ by 0.3-0.5 seconds from these starting points.

Support Strategy for Miniatures

Supports make or break miniature prints. Too few and the model fails. Too many and you spend twenty minutes removing them and filling divots. Here's the approach that minimizes both risks:

Orientation: Angle the miniature 15-30 degrees backward (leaning away from the build plate). This reduces the cross-sectional area of each layer, which means fewer islands, less suction force on the FEP, and more gradual transitions for overhangs like outstretched arms and cloaks.

Support density: Use medium supports (0.3-0.4 mm contact points) on the body and heavy supports (0.5 mm) under the base. For delicate areas like faces, sword tips, and thin accessories, switch to light supports (0.2 mm contact points) and place them manually.

Manual placement rules:

  • Support every island (disconnected area), the slicer usually catches these, but verify manually
  • Support the lowest point of every overhang, then add supports every 2-3 mm along the overhang edge
  • Avoid placing supports directly on faces, hands, and visible flat surfaces, put them on the back or underside
  • Place supports on areas that will be hidden by the base or by painting (under cloaks, inside shield backs)
Pro tip: Use Lychee Slicer's island detection feature to identify unsupported areas automatically. It highlights potential failure points in red, which saves you from discovering them mid-print as floating resin blobs.

Post-Processing Workflow

Raw resin prints aren't ready for the painting table. Here's the post-processing chain for every batch of miniatures:

  1. Wash in IPA (99%) for 2-3 minutes in an ultrasonic cleaner or wash station. Don't over-wash, more than 5 minutes in IPA makes the surface chalky and brittle.
  2. Remove supports while the resin is still slightly soft from washing. Use flush cutters and snip as close to the model surface as possible. Supports are much easier to remove before full UV curing.
  3. Cure under UV light for 3-5 minutes per side (6-10 minutes total) in a curing station. Rotate the model halfway through for even curing. Over-curing makes the resin brittle and can yellow lighter colors.
  4. Clean up support marks with a hobby knife or fine-grit sanding stick (400-600 grit). A small dab of liquid resin on a support nub, cured with a UV flashlight, can fill any divots cleanly.
  5. Prime before painting. Cured resin is smooth and non-porous, so paint doesn't grip well without a primer coat. Use a grey or white spray primer designed for miniatures (Citadel, Vallejo, or Army Painter) applied in thin, even coats.

Common Miniature Printing Problems

Loss of fine detail (mushy faces, soft edges): Over-exposure. Reduce normal exposure by 0.2-0.3 seconds. Light bleeds sideways through the resin, expanding features and filling in recesses. This is the most common mistake with miniatures.

Failed supports and dropped models: Under-exposure or insufficient support density. Increase bottom exposure by 5 seconds and add medium supports under any large flat overhangs (shields, cloaks, bases).

Visible layer lines on curved surfaces: Reduce layer height from 0.05 mm to 0.03 mm. If you're already at 0.03 mm and still see lines, the model's geometry might benefit from a slight orientation change to shift the layer transitions to less visible areas.

Warping or curling of thin features: Increase light-off delay to 2-3 seconds. This gives each layer more time to settle before the next exposure, reducing internal stress that causes warping on thin swords, staffs, and banner poles.

Quality benchmark: A well-printed 32 mm miniature should have clearly defined facial features visible under a magnifying glass, no visible layer lines at arm's length, and clean support removal marks that disappear under a coat of primer. If you're hitting all three, your settings are dialed in.

Resin printing miniatures is one of the most satisfying applications of desktop 3D printing. The detail quality rivals commercial injection molding at a fraction of the cost per model. Start with a popular test model like a heroic knight or a dragon, dial in your exposure with a calibration test, and build your army from there.

Building your resin workflow? Read our resin printing beginner's guide and our comparison of the best resin printers in 2026 to find the right machine for your miniature printing setup.

Published by the 3D Printer Stuff editorial team. Published October 8, 2026.

Editorial responsibility: see Imprint.

Spotted an error or have something to add? corrections@3dprinterstuff.com

Share with fellow makers:
resinminiaturessettingsguide
📖

Explore more

All articles on 3D Printer Stuff →

🔧

Maker Tips, Delivered

New guides, filament tests, and project ideas — every week in your inbox.

🎁 Free bonus: 3D Printing Starter Checklist (PDF)

🧭Part of our topic hub: Print Settings & Calibration→

You might also like

Comments (0)

Leave a comment

Comments are reviewed before publishing.